Dear Dr. Rossi,
In your promotion of the SKLed lamp it is said to be the most energy-efficient lamp ever made. However, no measure on the efficiency is given. I apologize if I am wrong. I have set up an Excel sheet calculation with a beamed light irradiating a plane perpendicular to the beam resulting in a circular illuminated area that is computed into Lux numbers. The Lux numbers are further computed into W. The Excel setup reflects approximately the SKLed (10,000 lm, 60 full apex angle, 5000K LED light spectrum). In this case there are uncertainties in computing irradiance and illuminance, however the result is 32 W. As the SKLed consumes 3.9 W the COP would be about 8.
1) Do you think COP 8 is reasonable?
2) Will you be announcing any COP for the SKLed?
Kind regards,
Calle H
You have put forward a space charge from; quantum vacuum fluctuations with virtual particle creation-annihilation / particle-antiparticle couples / virtual charge pairs, as one possible scenario that would provide localized electrostatic screening to facilitate the balancing of electron forces, enabling multiple electrons to position at close distances.
For the various scenario’s put forward the outcome is the same, on attaining a critical density of in-phase electrons that are in a low entropy state / environment, forces external to electrons then bring electrons closer together against coulomb repulsive forces that would push apart, allowing electrons to be held in a point of balance position at a close distance, this close positioning of in-phase electrons allowing build-up of a dense low entropy coherent charge cluster, depending on the environment they are associated with charge clusters can be small and transitory, interact with other electrons, interact with atoms, or build up to be visibly large and persist for relatively long periods of time.
If virtual particles do exist, maybe they relate to zero-point energy / vacuum energy / scalar potential energy waves emanating from a multitude of directional locations interfering with each other with fluctuating local maxima / minima, so short period localized points with peaks of energy, sometimes extreme, these energy peaks associated with creation-annihilation of virtual particles.
Maybe it is not necessary to have the existence of virtual particles, just the provision of sufficient localized energy and associated forces from gradients in this energy.
Dear Dr Andrea Rossi,
1 At what temperature it is possible to operate Ecat SKLed
2 With which voltage range 12V works Ecat SKLed
3 Where is the brightness regulator Ecat SKLed
Dear Dr Andrea Rossi,
In a scale from 1 to 10 which number would you pick as an index of difficulty of the work you are doing with the Ecat SKL ?
Cheers,
Donna
Dear Andrea,
There are a number of positron generators capable of providing directed streams available for test purposes. Have you considered using one to determine if there is any possibility of enhancing your energy output?
Testing regards.
Will you present in December 2021 also the model of the SKLed with assembly fits for mounting on street pole, to lighting the street?
The street pole model of SKLed will significant boost demand.
To add to my question,
We know that the electron converts to a 511 Kev photon when it encounters a positron with the same energy. Is some of this energy adding to your harvest?
More curious regards.
Dear Andrea,
I understand that your theory for extraction of energy from the vacuum depends upon the interaction of vibrations exhibited by the electrons(ZBG). My question is: Do you think that these vibrations in the vacuum fields(hf) interacting with the fields, create new photons whose energy is part of what you observe?
Curious regards.
Regarding the SKLed delivery
– Who will pay for the delivery cost when a lamp is ordered?
– From where will the SKLed be shipped, USA, Asia, Europe, scandinavia? (regarding customs costs)
On Power Engineering issue of September 14 2021:
Climate change irony: extreme weather leading to coal-fired comeback in many energy-intensive regions
Rod Walton
Dear Andrea
That SKLed is possible to dim is excellent.
In mine outdoor lamps today I use a led bulb that draws 3.9W and gives 265 lumens, that is sufficient. The light color is 2700K. Light angle is 25-deg.
Will SKLed be able to be regulated/filter adjusted to around that?
Sincerely, Svein H. Vormedal
Joys Del Sol:
Please go to http://www.ecat.com
to fond the order form of the Ecat SKLed.
The SK is only leased for industrial facilities ( see http://www.ecatskdemo.com ), while for the SKL we foresee the commercialization for the next year.
Warm Regards,
A.R.
I am here after a few years. Can someone please update me on the commercialisation schedule of E-cat devices ( both industrial and domestic ) esp. electricity generating ones? When will they be available for purchase online?
Dear Andrea.
What are the possibilities of reducing the intense luminous flux from SKLed to much lower levels when this is desirable?
What is the ability to change the color to suit different uses?
Sincerely, Svein H. Vormedal
Jean Paul Renoir:
No.
The so called “color temperature” of a luminous source corresponds to the temperature of the black body that emits the radiations with the same cromaticity ( = color ) of that luminous source.
Warm Regards,
A.R.
Dr Rossi,
when I read that a lamp has a color temperature of 5000 K, does this mean that the light bulb reaches inside 6ooo K of temperature ?
If not, what does that mean ?
Thanks,
JPR
Dear Andrea.
The E-CatSKLed lamp seems to me to be very relevant as a light source outdoors for any property, with a non-dazzling light beam towards walkways, terraces and plantings. Especially if it also had a small accumulator built in that was supplied with E-CatSKL charge.
In such contexts, there will be need for adjusting the brightness in relation to the areas of use and automatic switch-off during the day.
1. Is a significant buildt in damping possible?
2. May the lamp withstand outdoor use?
3. May the lamp be equipped with a photocell?
4. May accumulator and SKL charge be possible?
Sincerely: Svein H. Vormedal
Sam:
Thank you for the link: by the way, this blog receives many interesting links not directly connected with the E-Cat, but I am delighted to see that this blog is also an interesting channel of information for our Readers,
Warm Regards,
A.R.
Calle H:
Moreless, yes.
Warm Regards,
A.R.
Dear Dr. Rossi,
In your promotion of the SKLed lamp it is said to be the most energy-efficient lamp ever made. However, no measure on the efficiency is given. I apologize if I am wrong. I have set up an Excel sheet calculation with a beamed light irradiating a plane perpendicular to the beam resulting in a circular illuminated area that is computed into Lux numbers. The Lux numbers are further computed into W. The Excel setup reflects approximately the SKLed (10,000 lm, 60 full apex angle, 5000K LED light spectrum). In this case there are uncertainties in computing irradiance and illuminance, however the result is 32 W. As the SKLed consumes 3.9 W the COP would be about 8.
1) Do you think COP 8 is reasonable?
2) Will you be announcing any COP for the SKLed?
Kind regards,
Calle H
Dear Andrea,
Within your ResearchGate paper;
http://www.researchgate.net/publication/330601653_E-Cat_SK_and_long_range_particle_interactions
You have put forward a space charge from; quantum vacuum fluctuations with virtual particle creation-annihilation / particle-antiparticle couples / virtual charge pairs, as one possible scenario that would provide localized electrostatic screening to facilitate the balancing of electron forces, enabling multiple electrons to position at close distances.
For the various scenario’s put forward the outcome is the same, on attaining a critical density of in-phase electrons that are in a low entropy state / environment, forces external to electrons then bring electrons closer together against coulomb repulsive forces that would push apart, allowing electrons to be held in a point of balance position at a close distance, this close positioning of in-phase electrons allowing build-up of a dense low entropy coherent charge cluster, depending on the environment they are associated with charge clusters can be small and transitory, interact with other electrons, interact with atoms, or build up to be visibly large and persist for relatively long periods of time.
If virtual particles do exist, maybe they relate to zero-point energy / vacuum energy / scalar potential energy waves emanating from a multitude of directional locations interfering with each other with fluctuating local maxima / minima, so short period localized points with peaks of energy, sometimes extreme, these energy peaks associated with creation-annihilation of virtual particles.
Maybe it is not necessary to have the existence of virtual particles, just the provision of sufficient localized energy and associated forces from gradients in this energy.
Regards,
Keith Thomson.
Dear Dr Andrea Rossi,
1 At what temperature it is possible to operate Ecat SKLed
2 With which voltage range 12V works Ecat SKLed
3 Where is the brightness regulator Ecat SKLed
Dear Andrea,
You indicate that the work on the E-Cat SKL is very difficult. Are you sure you will be able to present a prototype of it on December 9th?
Best wishes,
Frank Acland
Donna:
10
Warm Regards,
A.R.
Sam:
Thank you for the link,
Warm Regards,
A.R.
Hello DR Rossi
Some LEDucation.
https://leducation.org/2021_presentations/
Regards
Sam
Dear Dr Andrea Rossi,
In a scale from 1 to 10 which number would you pick as an index of difficulty of the work you are doing with the Ecat SKL ?
Cheers,
Donna
eernie1:
I know those plants, but they have nothing to do with our technology.
Warm Regards,
A.R.
Dear Andrea,
There are a number of positron generators capable of providing directed streams available for test purposes. Have you considered using one to determine if there is any possibility of enhancing your energy output?
Testing regards.
Jaroslaw Bem:
No, but it is easy to adapt,
Warm Regards,
A.R.
Dear Andrea Rossi,
Will you present in December 2021 also the model of the SKLed with assembly fits for mounting on street pole, to lighting the street?
The street pole model of SKLed will significant boost demand.
Best regards,
Jaroslaw Bem
eernie1:
So far I just confirm what is written on
http://www.researchgate.net/publication/330601653_E-Cat_SK_and_long_range_particle_interactions
Warm Regards,
A.R.
Weleda:
Yes,
Warm Regards,
A.R.
Dear Dr Andrea Rossi,
Are electronics the main support of the progress you made with the Ecat SKL ?
Weleda
To add to my question,
We know that the electron converts to a 511 Kev photon when it encounters a positron with the same energy. Is some of this energy adding to your harvest?
More curious regards.
Dear Andrea,
I understand that your theory for extraction of energy from the vacuum depends upon the interaction of vibrations exhibited by the electrons(ZBG). My question is: Do you think that these vibrations in the vacuum fields(hf) interacting with the fields, create new photons whose energy is part of what you observe?
Curious regards.
RS:
1- the Client
2- it will depend on the destination
Warm Regards,
A.R.
Regarding the SKLed delivery
– Who will pay for the delivery cost when a lamp is ordered?
– From where will the SKLed be shipped, USA, Asia, Europe, scandinavia? (regarding customs costs)
Rod Walton:
Thank you for the update,
Warm Regards,
A.R.
On Power Engineering issue of September 14 2021:
Climate change irony: extreme weather leading to coal-fired comeback in many energy-intensive regions
Rod Walton
Gavino Mamia:
We are working very, very hard.
Warm Regards,
A.R.
Dott. Rossi
Sbrigati ti prego, ci vogliono massacrare
https://notizie.tiscali.it/economia/articoli/aumenti-bolletta-elettrica-stangata-famiglie/
Anonimo:
Una cosa sicura invece è che dopo la presentazione tu salterai i pasti, dato che non ci sarà più nessuno a pagarti
CC:
10000 Lumens, since 1 m^2 = 10000 cm^2
Warm Regards,
A.R.
Anonymous:
Thankyou for your opinion,
Warm Regards,
A.R.
Norma:
Yes,
Warm Regards,
A.R.
Dear Dr Andrea Rossi:
Still solid the calendar of the presentation in Stockholm ?
I am sure before December you will find an excuse to skip the presentation
Dr Rossi:
1 Lux = 1 Lumen/square meter. If the same luminous flux is focused on 1 square centimeter, how many Lumens do we obtain ?
CC
Svein H. Vormedal:
Yes,
Warm regards,
A.R.
Dear Andrea
That SKLed is possible to dim is excellent.
In mine outdoor lamps today I use a led bulb that draws 3.9W and gives 265 lumens, that is sufficient. The light color is 2700K. Light angle is 25-deg.
Will SKLed be able to be regulated/filter adjusted to around that?
Sincerely, Svein H. Vormedal
Svein H. Vormedal:
The lumens are dimmable, the color cannot be changed, unless filters are applied.
Warm Regards,
A.R.
Joys Del Sol:
Please go to
http://www.ecat.com
to fond the order form of the Ecat SKLed.
The SK is only leased for industrial facilities ( see http://www.ecatskdemo.com ), while for the SKL we foresee the commercialization for the next year.
Warm Regards,
A.R.
I am here after a few years. Can someone please update me on the commercialisation schedule of E-cat devices ( both industrial and domestic ) esp. electricity generating ones? When will they be available for purchase online?
Dear Andrea.
What are the possibilities of reducing the intense luminous flux from SKLed to much lower levels when this is desirable?
What is the ability to change the color to suit different uses?
Sincerely, Svein H. Vormedal
Jean Paul Renoir:
No.
The so called “color temperature” of a luminous source corresponds to the temperature of the black body that emits the radiations with the same cromaticity ( = color ) of that luminous source.
Warm Regards,
A.R.
Dr Rossi,
when I read that a lamp has a color temperature of 5000 K, does this mean that the light bulb reaches inside 6ooo K of temperature ?
If not, what does that mean ?
Thanks,
JPR
@Prof
With 69000 readings, the paper
http://www.researchgate.net/publication/330601653_E-Cat_SK_and_long_range_particle_interactions
is the most read physics paper of Researchgate
Best
Roberto
Bernie Morrissey:
No,
Warm Regards,
A.R.
Svein H. Vormedal:
1- I do not understand
2- yes
3- yes
4- for the SKL yes, for the SKLed no
Warm Regards,
A.R.
Dear Andrea.
The E-CatSKLed lamp seems to me to be very relevant as a light source outdoors for any property, with a non-dazzling light beam towards walkways, terraces and plantings. Especially if it also had a small accumulator built in that was supplied with E-CatSKL charge.
In such contexts, there will be need for adjusting the brightness in relation to the areas of use and automatic switch-off during the day.
1. Is a significant buildt in damping possible?
2. May the lamp withstand outdoor use?
3. May the lamp be equipped with a photocell?
4. May accumulator and SKL charge be possible?
Sincerely: Svein H. Vormedal
Dear Andrea Rossi,
The Ecat SKLed has to be connected to external power to start. After startup can it be unplugged?
Thank you
Bernie Morrissey
Prof:
Thank you for the update,
Warm Regards,
A.R.
Dear Andrea:
Your paper
http://www.researchgate.net/publication/330601653_E-Cat_SK_and_long_range_particle_interactions
has reached today the record of
Readings 69000
and counting…
Cheers,
Prof
Sam:
Thank you for the link: by the way, this blog receives many interesting links not directly connected with the E-Cat, but I am delighted to see that this blog is also an interesting channel of information for our Readers,
Warm Regards,
A.R.
Patrick:
Yes, in multiple fields. The potential is enormous, also due to indirect applications.
Warm Regards,
A.R.
Dear Andrea,
Do you think the ecat will also generate a significant amount of jobs, and if yes, in what discipline?
Regards,
Patrick
Hello DR Rossi
New discovery in Ceramics.
https://techxplore.com/news/2021-09-max-phase-ceramics-self-heal-room-temperature.amp
Regards
Sam