Regarding the thermal output of the eCat-SK, have you verified that the thermal output levels as measured by radiometric means closely corresponds to measurements using:
1. change in flowing water temperature without phase transition; and
2. change in water phase (i.e., production of steam)?
3. If so, have you also made measurements of either or both of the above at some reduced output power?
Rodney Nicholson:
The commentator is right in both cases. If you listen carefully the video (that today has been updated and made easier to listen, just go to http://www.ecatskdemo.com ), you will see that when the commentator reads the oscilloscope he specifies that that is the voltage of the current that enters the E-Cat SK; when he reads the voltage of the Amperometer-Voltmeter he specifies that it measures the voltage that enters the control panel: only a very small part of the energy that is consumed by the control panel is consumed by the E-Cat, because most of it goes to the cooling system.
Warm Regards,
A.R.
Mason Ruckel:
We do not have any licensee, with or without exclusive, in Australia.
AND THE FOLLOWING IS FOR ALL THE READERS
Attention: please, if anybody receives offers related to our service from persons that say they are our representative or licensees, do not sign or pay anything before contacting us ( INFO@LEONARDOCORP1996.COM ) to verify if such person or organization is authorized to act on behalf of us.
In the specific case of Australia, whomever offers our services is not authorized.
Warm Regards,
A.R.
Dr Andrea Rossi:
Do you have any representative or licensee with or without exclusive in Australia?
There is a guy around that says he is a non exclusive representative for Leonardo in Australia.
Thank you if you can answer.
Mason Ruckel
Thank you for the presentation. There is one point on which I am confused (or perhaps I should say: ” …. about which I know I am confused.”):
At 10:35 in the video, the oscilloscope showed that the voltage – to quote the commentator – “of the electric energy that enters the E-Cat SK” is 250 millivolts. That, I thought I understood.
But later in the video – at 12:25 – the same commentator says that the volt meter “……. is displaying the voltage that is going into the E-Cat.” He then says that is 19 volts.
It would be helpful to me if my confusion about this could be disentangled (and I am hoping that a knowledge of quantum mechanics will not be a pre-requisite for understanding it!)
Alessandro Coppi:
Thank you for your opinion, but the presentation has been organized by me in the fashion I decided was the right one. The rawness was a precise choice and the fact that I have not been filmed was a precise choice too.
I wanted to avoid any embellishment and render the situation such that nothing could attract the attendant but the core of the issue, also to avoid to lose time with persons that have not been able to get the core of the issue. We are in the pioneer phase of the marketing, not in the mass phase.
Sincerely, from the feedback in the aftermath, I can see that most of the audience, especially the one that was the target of the presentation, appreciated it as it was, but it is correct to respect all the opinions. Maybe I am wrong.
Thank you for your attention to our work,
Warm Regards,
A.R.
Hi Andrea,
I saw the whole presentation of the E-CAT SK on the 31st january, and congratulate for the big effort and success in bringing this technology to the market, but looking at the streaming, a question is bouncing: why a so raw realization? no presentation of the persons involved in, only one instead of at least two cameras for different and more detailed images … your face appears in the video, only one second because you lowered yourself.
Today I believe to know the motivation of this choice: your target is to not to reach too many clients, perhaps because your production capacity, the logistic and installation organization does not support a gigantic volume of requests, and perhaps the E-CAT SK need of test for more time for reliability.
This is your approach, and I respect this, also because everyone has to take the step according to the leg, unluckily, this way will take more time for the global diffusion, and the world needs it as soon as possible.
By the way, do not worry much for IP, there is enough room for everybody in this field, and you are the one that named this technology with his first name and surname.
Very honoured to have sharing with you the same time over this earth.
Alessandro Coppi
Dear Dr. Rossi,
I saw your online advertising, and I like it, many compliments.
I would still like that those ads like this would be widespread everywhere. It seems in fact that this time the media (newspapers, TV, etc.) have not been aware of your presentation, except for a few isolated cases.
I hope anyway that you have been satisfied with the response of the market. This is the main thing.
Sam:
I do not understand your question: can you rephrase it?
You can see the whole demo on youtube an here: http://www.ecatskdemo.com
Warm Regards,
A.R.
Frank Acland:
First of all, let me remind that the whole presentation video is on youtube and here http://www.ecatskdemo.com
Answers:
1- we can produce the Ecat SK that we will need
2- the Ecat SK gives the T that is demanded by means of a thermostat
3- yes
4- it is totally recyclable
5- it is done every day by the Customers. See the video.
6- I explained in the video all the information that we do not deem confidential. Our clients do not need further technological particulars.
7- see our US Patent
8- confidential
Warm Regards,
A.R.
I have compiled here the list of questions that I have received since the presentation last week that we were not able to cover during the live event.
1. About production capacity — how many reactors can you produce per month and how quickly he can double the production of reactors?
(Remember Tesla’s “production hell”)
2. I understand that the E-Cat SK module installed as a room heater is probably in the North Central United State. As opposed to the reported outside temperature of around 0 C or 32F, nearly that entire region was reporting numbers like -20 to -30F. Did the SK module, responding to the demands of a thermostat, manage say the day of the presentation?
3. Has the presentation of Thursday so far generated interest from potential new customers?
4. What happens with the used fuel? Is a kind of recycling possible?
5. When will be the first test of the SK with a flow calorimeter (as done in the Stockholm demonstration) ?
6. Is the blue plasma in the center of the two orange plasma’s a “fireball” with a double layer? If so, are the two orange plasma’s the cathode and anode? If not, please explain what we are seeing.
7. Is Lithium Aluminum Hydride the only fuel component of the SK?
8. Is there any ordinary atmosphere in the fuel mixture?
Time is running out to counter climate change, we must go fast and strong in the deployment of the E-Cat. I really think that only an industrialist of international rank will be able to ensure promotion and massive diffusion of the reactor, potentially millions of units per month.
Just look at the YouTube counter: at this moment 4804 views, against millions around the world when an a new car is launched.
The fact that the current client does not communicate is also a drag on diffusion: I hope that future customers will be less cautious.
I have no doubt that many captains of industry would be interested in this technology, energy being a major theme for humanity.
If an invention has a large sales potential, it will undoubtedly interest the industry. IP purchases are often traded in billion$
Caro Dr. Rossi ,
il 31 Gennaio 2019 è iniziata una nuova era per l’umanità . Grazie dal profondo del cuore . Grazie allo Scienziato e grazie all’Uomo . Dio La benedica .
ENGLISH:
January 31st 2019 has been the first day of a new era for mankind. Thank you with all my heart, thanks to the scientist and the man. God bless you,
Armando
“Have you considered selling the invention to an industrialist? This is common in the industry, I am thinking of biotechnology, where innovative molecules are often bought at very high prices to start-ups.”
= = = = = = = = =
I think the two principal answers to the above suggestion are rather straightforward:
A) No one has several trillion dollars to spare, with which to make payment for it.
B) No doubt also, Mr. Rossi derives so much enjoyment from his continuing quest to perfect the products he is developing from his invention, why would he want to give that up? I can imagine that when he runs out of ideas he might change his mind. But it doesn’t appear likely that that will happen any time soon!
Dear Andrea,
About your answer to John Evans: if one control panel can control 10 modules the COP should be ten folds higher, isn’t it true?
Warm Regards,
Chuck Davis
Clovis Ray:
Thank you for your empathy: yes, I must admit that the last 3-4 years have been very hard, but here I am, still working hard.
Same wishes for you and your family,
Warm Regards,
A.R.
Dear Dr Rossi,
Great presentation!
The world will thank you forever.
Man, what a weight I saw on your shoulders after these year of work, that now has unveiled itself magnificent.
I pray for your health and for your family.
Be well,
Clovis Ray
We have been looking forward to the presentation of the commercial product E-Cat SK for a very long time.
The expectations were therefore very high.
It continues to amaze me how erudite our friend Andrea Rossi and his entourage are.
Nowadays product presentations are often held with lots of blingbling, big stages and immense video and spectacle.
None of this was used here.
An old, hoarse man, who comes into the picture even without a head but with a yellow tie, calmly says that this blue pedal bin is a hypermodern, nuclear plasma reactor that multiplies the incoming energy at least fifty times.
Then we get some technical images, where 99% of the population will click away after one minute.
And so it goes on.
Regardless of IT high-tech times, the calculations are done with pencil and paper, which even contains an error, and half of the explanation goes to conversion from the metric to the imperial system. In addition, corrections have been made with corrector fluid. I would not know where to buy that.
A person would not dare to forward such a video to his family or friends.
But …. appearances are deceiving.
If you pay attention, and you have sufficient knowledge and insight to look through this seeming clumsy, you will see a following wonder of the world.
“clumsiness” is with a wink: “Hand made by Andrea Rossi”, I think will go into history in the same way as Vincent Van Gogh, Gustav Klimt, Pablo Picasso, Michelangelo or P.P. Rubens.
He had once promised me in a distant past that I would get some of his discarded prototypes, but he seems to forget that over and over again.
In addition, a technical manager will immediately recognize all the essential characteristics of the product: efficiency, robustness, simplicity, service.
Another important aspect: this is about nuclear energy, so wannabe youtube jokers will never get to such a device. This is for professionals.
There was no better way to make this presentation for the right target group.
– I was able to look at the whole presentation now, and I also agree with your calculations (except maybe with the ‘calorimetric comparision’, where I found another result for the Power needed to heat up the air from 0°C to 16°C: As the Cp of air is 1 J/(kg*K), I found: Power = 6700(kg/h)*1(J/(kg*K))*16K = 107200J/H = (107200/3600)Watt = 29.78 Watt, but I was quick, and maybe I’m wrong?)
– But in the youtube video, at about 22 minutes and 45 seconds, you said something special about the 437.2nm (nanometer) signature, where you said that that possibly is the origin of the energy gain. Could you elaborate on that?
– Many congratulations because you succeeded to let a plasma dance like a ballerina, while the hot fusion community still (and maybe never) will be able to do so. I wish you all success with your further work and the commercialization of the E-Cat SK!
Kind Regards,
Daniel.
P.S. Although I more like the first version on his first solo LP (‘Astral Weeks’), here a link to a live version of Van Morrisons’ song ‘Ballerina’ 😉 : https://www.youtube.com/watch?v=IfaaaDX_Uh0
Dear Andrea, I would have stared at the beautiful plasma dancing for hours… and actually I stared at it for two hours… I suggest that in one of the next iteration of the design of the external case, you could add (as a luxury option) a 12″-13″ LED screen projecting a video captured in real time by a little camera inside the reactor, in the same way you made at the presentation.
Dear Andrea,
There are many parts of this world that need heat only for one portion of the year, but doesn’t need a lot of heat during the rest of the year for their commercial buildings. My home town of Chicago is an example. Can you install a profitable system in a location that for instance only needs heat for 25% of the year?
Have you considered selling the invention to an industrialist? This is common in the industry, I am thinking of biotechnology, where innovative molecules are often bought at very high prices to start-ups.
On the presentation itself I regret that your client did not intervene, figures in hand. It would have given resonance to your presentation.
Dear Andrea:
I have to admit I was wanting to see a more dramatic presentation. I had hoped excitement could generate more attention to your work. I do understand though this may not have been your purpose for the event, it was mainly for potential buyers. But I have one question on the math. If 1 controller using 380 wh/h for 1 ecatsk has a cop of 57 what is the power consumption of 1 controller managing multiple units? if its power usage is not increased by 380 wh/h for each ecatsk unit and the controller can operate many units wouldn’t the cop be much greater?
Good luck and thank you.
John C Evans
Dear Andrea Rossi,
Regarding the thermal output of the eCat-SK, have you verified that the thermal output levels as measured by radiometric means closely corresponds to measurements using:
1. change in flowing water temperature without phase transition; and
2. change in water phase (i.e., production of steam)?
3. If so, have you also made measurements of either or both of the above at some reduced output power?
Rodney Nicholson:
The commentator is right in both cases. If you listen carefully the video (that today has been updated and made easier to listen, just go to http://www.ecatskdemo.com ), you will see that when the commentator reads the oscilloscope he specifies that that is the voltage of the current that enters the E-Cat SK; when he reads the voltage of the Amperometer-Voltmeter he specifies that it measures the voltage that enters the control panel: only a very small part of the energy that is consumed by the control panel is consumed by the E-Cat, because most of it goes to the cooling system.
Warm Regards,
A.R.
Mason Ruckel:
We do not have any licensee, with or without exclusive, in Australia.
AND THE FOLLOWING IS FOR ALL THE READERS
Attention: please, if anybody receives offers related to our service from persons that say they are our representative or licensees, do not sign or pay anything before contacting us ( INFO@LEONARDOCORP1996.COM ) to verify if such person or organization is authorized to act on behalf of us.
In the specific case of Australia, whomever offers our services is not authorized.
Warm Regards,
A.R.
Dr Andrea Rossi:
Do you have any representative or licensee with or without exclusive in Australia?
There is a guy around that says he is a non exclusive representative for Leonardo in Australia.
Thank you if you can answer.
Mason Ruckel
Hi Andrea:
Thank you for the presentation. There is one point on which I am confused (or perhaps I should say: ” …. about which I know I am confused.”):
At 10:35 in the video, the oscilloscope showed that the voltage – to quote the commentator – “of the electric energy that enters the E-Cat SK” is 250 millivolts. That, I thought I understood.
But later in the video – at 12:25 – the same commentator says that the volt meter “……. is displaying the voltage that is going into the E-Cat.” He then says that is 19 volts.
It would be helpful to me if my confusion about this could be disentangled (and I am hoping that a knowledge of quantum mechanics will not be a pre-requisite for understanding it!)
Thank you.
Entangled regards,
Rodney.
Fabrizio Sgorlon:
Grazie!
Cari saluti,
A.R.
In Honor of
Dr Andrea Rossi
and to remember
Prof Sergio Focardi
“”— e il Gatto gioco’…e gioco’….guardo’….il FUOCO.!!
..ci giro’ attorno….lo annuso’..
.gioco’.e gioco’..ancora..e capi’ che il FUOCO era amico…non scottava..
e si accovaccio’ ..accanto …a fare le fusa…
..nemmeno gli Scienziati capirono….le fusa del GATTO..
..ma perche’…come!…non e’ possibile!..un gatto non gioca col fuoco!! Risero…!!
ma alla fine …. il Mondo ..stette a guardare…attonito e . sbalordito…!.
…il Gatto con le Fusa… accanto al Fuoco..!.””
Bravo ,Bravissimo Dr.Andrea Rossi.
Best Regards
a simple farmer
from Jesolo Italy
fabrizio sgorlon
Albert Ellul:
We make in series only the Ecat SK.
Warm Regards,
A.R.
Peter Wolstenholm:
Thank you for the information,
Warm Regards,
A.R.
Dr Rossi:
The AGA Cooker is this:
http://www.agaliving.com/aga-range-cookers
What is the smallest sized E-cat QX in production.
Alessandro Coppi:
Thank you for your opinion, but the presentation has been organized by me in the fashion I decided was the right one. The rawness was a precise choice and the fact that I have not been filmed was a precise choice too.
I wanted to avoid any embellishment and render the situation such that nothing could attract the attendant but the core of the issue, also to avoid to lose time with persons that have not been able to get the core of the issue. We are in the pioneer phase of the marketing, not in the mass phase.
Sincerely, from the feedback in the aftermath, I can see that most of the audience, especially the one that was the target of the presentation, appreciated it as it was, but it is correct to respect all the opinions. Maybe I am wrong.
Thank you for your attention to our work,
Warm Regards,
A.R.
Sam:
The name we have chosen for the control panel is:
CONCERTO
Warm Regards,
A.R.
What was the winning name of the name
the E-Cat software contest or have you
not picked a winner yet.
Hi Andrea,
I saw the whole presentation of the E-CAT SK on the 31st january, and congratulate for the big effort and success in bringing this technology to the market, but looking at the streaming, a question is bouncing: why a so raw realization? no presentation of the persons involved in, only one instead of at least two cameras for different and more detailed images … your face appears in the video, only one second because you lowered yourself.
Today I believe to know the motivation of this choice: your target is to not to reach too many clients, perhaps because your production capacity, the logistic and installation organization does not support a gigantic volume of requests, and perhaps the E-CAT SK need of test for more time for reliability.
This is your approach, and I respect this, also because everyone has to take the step according to the leg, unluckily, this way will take more time for the global diffusion, and the world needs it as soon as possible.
By the way, do not worry much for IP, there is enough room for everybody in this field, and you are the one that named this technology with his first name and surname.
Very honoured to have sharing with you the same time over this earth.
Alessandro Coppi
Italo R.:
We reached the target we wanted to reach now. I am more than satisfied.
Warm Regards,
A.R.
Dear Dr. Rossi,
I saw your online advertising, and I like it, many compliments.
I would still like that those ads like this would be widespread everywhere. It seems in fact that this time the media (newspapers, TV, etc.) have not been aware of your presentation, except for a few isolated cases.
I hope anyway that you have been satisfied with the response of the market. This is the main thing.
Kind Regards,
Italo R.
Sam:
I do not understand your question: can you rephrase it?
You can see the whole demo on youtube an here:
http://www.ecatskdemo.com
Warm Regards,
A.R.
Armando Sbrana:
Thank you for your sustain to our Team,
Warm Regards,
A.R.
Karl Henrik Malmqvist:
THANK YOU !!!
Warm Regards,
A.R.
Frank Acland:
First of all, let me remind that the whole presentation video is on youtube and here
http://www.ecatskdemo.com
Answers:
1- we can produce the Ecat SK that we will need
2- the Ecat SK gives the T that is demanded by means of a thermostat
3- yes
4- it is totally recyclable
5- it is done every day by the Customers. See the video.
6- I explained in the video all the information that we do not deem confidential. Our clients do not need further technological particulars.
7- see our US Patent
8- confidential
Warm Regards,
A.R.
Fern Sievert:
Yes, in full.
Warm Regards,
A.R.
Hello DR Rossi
Did you pick the name for the E-Cat SK
software or maybe I missed it in the Demo.
Good luck in the market with your product.
Regards
Sam
Dear Dr Andrea Rossi:
Surely you had a precise target when you organized the presentation of the Ecat SK: did you reach your target?
Dear Andrea,
I have compiled here the list of questions that I have received since the presentation last week that we were not able to cover during the live event.
1. About production capacity — how many reactors can you produce per month and how quickly he can double the production of reactors?
(Remember Tesla’s “production hell”)
2. I understand that the E-Cat SK module installed as a room heater is probably in the North Central United State. As opposed to the reported outside temperature of around 0 C or 32F, nearly that entire region was reporting numbers like -20 to -30F. Did the SK module, responding to the demands of a thermostat, manage say the day of the presentation?
3. Has the presentation of Thursday so far generated interest from potential new customers?
4. What happens with the used fuel? Is a kind of recycling possible?
5. When will be the first test of the SK with a flow calorimeter (as done in the Stockholm demonstration) ?
6. Is the blue plasma in the center of the two orange plasma’s a “fireball” with a double layer? If so, are the two orange plasma’s the cathode and anode? If not, please explain what we are seeing.
7. Is Lithium Aluminum Hydride the only fuel component of the SK?
8. Is there any ordinary atmosphere in the fuel mixture?
Dear Andrea,
The link from Lars Svensson to the article in the Norwegian newspaper Aftenposten (The Evening Post) doesn´t work. Here is a google translation of the article.
https://translate.google.com/translate?sl=no&tl=en&u=https%3A%2F%2Fwww.aftenposten.no%2Fnorge%2Fi%2F0ERWbA%2FHevder-a-ha-revolusjonerende-energi-til-salgs.
Best Regards,
Karl-Henrik
Dear Rodney,
Time is running out to counter climate change, we must go fast and strong in the deployment of the E-Cat. I really think that only an industrialist of international rank will be able to ensure promotion and massive diffusion of the reactor, potentially millions of units per month.
Just look at the YouTube counter: at this moment 4804 views, against millions around the world when an a new car is launched.
The fact that the current client does not communicate is also a drag on diffusion: I hope that future customers will be less cautious.
I have no doubt that many captains of industry would be interested in this technology, energy being a major theme for humanity.
If an invention has a large sales potential, it will undoubtedly interest the industry. IP purchases are often traded in billion$
Regards,
Michel
Caro Dr. Rossi ,
il 31 Gennaio 2019 è iniziata una nuova era per l’umanità . Grazie dal profondo del cuore . Grazie allo Scienziato e grazie all’Uomo . Dio La benedica .
ENGLISH:
January 31st 2019 has been the first day of a new era for mankind. Thank you with all my heart, thanks to the scientist and the man. God bless you,
Armando
Michel
February 1, 2019 at 1:57 PM
“Dear Dr Rossi,
“Have you considered selling the invention to an industrialist? This is common in the industry, I am thinking of biotechnology, where innovative molecules are often bought at very high prices to start-ups.”
= = = = = = = = =
I think the two principal answers to the above suggestion are rather straightforward:
A) No one has several trillion dollars to spare, with which to make payment for it.
B) No doubt also, Mr. Rossi derives so much enjoyment from his continuing quest to perfect the products he is developing from his invention, why would he want to give that up? I can imagine that when he runs out of ideas he might change his mind. But it doesn’t appear likely that that will happen any time soon!
Rodney.
Lars Svensson:
Thank you for the reference!
Warm Regards,
A.R.
Chuck Davis:
No, it is not true, because it is not so simple.
Warm Regards,
A.R.
Dear Andrea,
About your answer to John Evans: if one control panel can control 10 modules the COP should be ten folds higher, isn’t it true?
Warm Regards,
Chuck Davis
Dr Rossi:
Aftenposten ( the major newspaper of Norway ) has published today a report about your presentation of yesterday:
https://www.aftenposten.no/article/ap-OERWbA.html
John C. Evans:
No, the COP would not be increased in assemblies.
Warm Regards,
A.R.
Michel:
I have explained also this fact during the presentation. Can go to http://www.ecatskdemo.com and see it all, if you like.
Warm Regards,
A.R.
Eernie1:
Yes.
Warm Regards,
A.R.
JPR:
Never say never.
I think I found the right partner,
Warm Regards,
A.R.
Daniel De Caluwe’:
To understand the importance of the signature 437.2 nm, please read my paper of January 24th 2019:
https://www.researchgate.net/publication/330601653_E-cat_SK_and_long_range_particle_interactions
Go to par 3 and 5, skip the math look at the essence of it.
About the rating, I confirm: it is 21.9, not 29.78 ( I wish it was…)
Warm Regards,
A.R.
Koen Vandewalle:
He,he,he…you forgot an alarming and revealing particular: falling in love with a plasma ballerina…
Warm Regards,
A.R.
Clovis Ray:
Thank you for your empathy: yes, I must admit that the last 3-4 years have been very hard, but here I am, still working hard.
Same wishes for you and your family,
Warm Regards,
A.R.
Dear Dr Rossi,
Great presentation!
The world will thank you forever.
Man, what a weight I saw on your shoulders after these year of work, that now has unveiled itself magnificent.
I pray for your health and for your family.
Be well,
Clovis Ray
We have been looking forward to the presentation of the commercial product E-Cat SK for a very long time.
The expectations were therefore very high.
It continues to amaze me how erudite our friend Andrea Rossi and his entourage are.
Nowadays product presentations are often held with lots of blingbling, big stages and immense video and spectacle.
None of this was used here.
An old, hoarse man, who comes into the picture even without a head but with a yellow tie, calmly says that this blue pedal bin is a hypermodern, nuclear plasma reactor that multiplies the incoming energy at least fifty times.
Then we get some technical images, where 99% of the population will click away after one minute.
And so it goes on.
Regardless of IT high-tech times, the calculations are done with pencil and paper, which even contains an error, and half of the explanation goes to conversion from the metric to the imperial system. In addition, corrections have been made with corrector fluid. I would not know where to buy that.
A person would not dare to forward such a video to his family or friends.
But …. appearances are deceiving.
If you pay attention, and you have sufficient knowledge and insight to look through this seeming clumsy, you will see a following wonder of the world.
“clumsiness” is with a wink: “Hand made by Andrea Rossi”, I think will go into history in the same way as Vincent Van Gogh, Gustav Klimt, Pablo Picasso, Michelangelo or P.P. Rubens.
He had once promised me in a distant past that I would get some of his discarded prototypes, but he seems to forget that over and over again.
In addition, a technical manager will immediately recognize all the essential characteristics of the product: efficiency, robustness, simplicity, service.
Another important aspect: this is about nuclear energy, so wannabe youtube jokers will never get to such a device. This is for professionals.
There was no better way to make this presentation for the right target group.
Thanks and once again a sincere congratulations,
Koen
Dear Dr. Rossi,
– I was able to look at the whole presentation now, and I also agree with your calculations (except maybe with the ‘calorimetric comparision’, where I found another result for the Power needed to heat up the air from 0°C to 16°C: As the Cp of air is 1 J/(kg*K), I found: Power = 6700(kg/h)*1(J/(kg*K))*16K = 107200J/H = (107200/3600)Watt = 29.78 Watt, but I was quick, and maybe I’m wrong?)
– But in the youtube video, at about 22 minutes and 45 seconds, you said something special about the 437.2nm (nanometer) signature, where you said that that possibly is the origin of the energy gain. Could you elaborate on that?
– Many congratulations because you succeeded to let a plasma dance like a ballerina, while the hot fusion community still (and maybe never) will be able to do so. I wish you all success with your further work and the commercialization of the E-Cat SK!
Kind Regards,
Daniel.
P.S. Although I more like the first version on his first solo LP (‘Astral Weeks’), here a link to a live version of Van Morrisons’ song ‘Ballerina’ 😉 : https://www.youtube.com/watch?v=IfaaaDX_Uh0
Orsobubu:
Intelligent idea,
Warm Regards
A.R.
David:
Thank you for your empathy,
Warm Regards
A.R.
Dear Andrea, I would have stared at the beautiful plasma dancing for hours… and actually I stared at it for two hours… I suggest that in one of the next iteration of the design of the external case, you could add (as a luxury option) a 12″-13″ LED screen projecting a video captured in real time by a little camera inside the reactor, in the same way you made at the presentation.
Do you think the gas turbine fueled by the Ecat SK will be the surprise of 2019?
Dear Andrea,
There are many parts of this world that need heat only for one portion of the year, but doesn’t need a lot of heat during the rest of the year for their commercial buildings. My home town of Chicago is an example. Can you install a profitable system in a location that for instance only needs heat for 25% of the year?
Regards
Dear Dr Rossi,
Have you considered selling the invention to an industrialist? This is common in the industry, I am thinking of biotechnology, where innovative molecules are often bought at very high prices to start-ups.
On the presentation itself I regret that your client did not intervene, figures in hand. It would have given resonance to your presentation.
Regards,
Michel
Dear Andrea:
I have to admit I was wanting to see a more dramatic presentation. I had hoped excitement could generate more attention to your work. I do understand though this may not have been your purpose for the event, it was mainly for potential buyers. But I have one question on the math. If 1 controller using 380 wh/h for 1 ecatsk has a cop of 57 what is the power consumption of 1 controller managing multiple units? if its power usage is not increased by 380 wh/h for each ecatsk unit and the controller can operate many units wouldn’t the cop be much greater?
Good luck and thank you.
John C Evans